
Ontario Fire Code Dust-Producing Processes Rules
Section 5.3 of the Ontario Fire Code in plain language, the points where it differs from the national code, and a collector checklist.
Estimate your cost
The Ontario Fire Code dust-producing processes rules sit in the Dust-Producing Processes section of the Fire Code, the Ontario regulation made under the Fire Protection and Prevention Act. They apply to any building or part of a building where combustible dust is produced in amounts that create a fire or explosion hazard, and cover cleaning, dust collection, where collectors may sit, bonding, explosion venting and ignition sources, with extra rules for woodworking and grain handling. Ontario's version follows the national code closely but differs in several places.
What are the Ontario Fire Code dust-producing processes rules?
Ontario's Section 5.3 requires vacuum cleaning with safe equipment, dust-collecting systems, collector location limits, bonding and grounding, explosion venting or prevention, interlocks, separators, ignition control, a minimum duct velocity and rules for storage vent stacks.
- 5.3.1.2 Dust removal. Surfaces kept clean with non-sparking, conductive, bonded equipment that removes dust by vacuum; compressed air only where vacuum fails, with ignition sources eliminated and machinery de-energized.
- 5.3.1.3 Dust-collecting systems. Provided to stop accumulation and keep suspended dust at a safe concentration, designed to good engineering practice, noncombustible, and spark-free at the fan.
- 5.3.1.4 Dust collectors. Above 2.36 m³/s, outside with venting of at least 0.1 m² per m³ of enclosure, or inside under one of three options; returned air must not create a hazard.
- 5.3.1.5 to 5.3.1.10. Bonding and grounding; venting to NFPA 68; prevention systems to NFPA 69; interlocks between equipment and its collection system; separators; and no open flames, sparks, heat or smoking unless controlled.
- 5.3.1.11 and 5.3.1.12. Ducts designed for at least 1068 m/min, and permanently open vent stacks for storage containers where mechanical collection is not practical.
Where does Ontario's Section 5.3 differ from the national code?
Ontario's Section 5.3 differs from the national code in several places: it requires NFPA 68 and NFPA 69 conformance outright, adds duct velocity and vent stack articles, limits the inside collector room to dust collection, and keeps a deeming clause for older wood exhausts.
| Article | Ontario Fire Code | National Fire Code 2020 |
|---|---|---|
| 5.3.1.2 | Cleaning equipment to the Electrical Safety Code under the Electricity Act, 1998 | Cleaning equipment to CSA C22.1, the Canadian Electrical Code |
| 5.3.1.4 (2) (c) | Inside room must also be used solely for dust-collecting equipment | Room with 1 h fire separations and outdoor venting |
| 5.3.1.6 (2) | Explosion venting designed in conformance with NFPA 68 | Good engineering practice such as that described in NFPA 68 |
| 5.3.1.7 (2) | Explosion prevention system in conformance with NFPA 69 | Good engineering practice such as that described in NFPA 69 |
| 5.3.1.11 | Duct air velocity of at least 1068 m/min | No such article |
| 5.3.1.12 | Vent stacks permitted for storage containers where mechanical collection is not practical | No such article (vent stacks only for grain bins) |
| 5.3.2.1 (3) | Woodworking exhaust systems that met the Code on December 31, 2025 are deemed to comply | No deeming clause |
| 5.3.2.3 | Extinguisher complying with Subsection 6.2.6, or a garden-type hose, within 7.5 m | Portable extinguisher within 7.5 m |
| 5.3.3.4 | Fog and fine spray nozzles on hose stations in dusty grain facilities | Nozzles to Sentence 3.2.5.11.(7) of the NBC |
The national rules, article by article, are on the national fire code page.
Does the collector location rule apply to my dust collector?
Ontario's collector location rule in Article 5.3.1.4 applies to any dust collector with a capacity over 2.36 m³/s, which must be outside with venting or inside under one of three protective options.
Does Article 5.3.1.4 apply to your collector? 5 questions
- Does the dust collector have a capacity greater than 2.36 m³/s?Yes: Go to question 2.No: Article 5.3.1.4 does not apply; the rest of Section 5.3 still does, and Regulation 851 section 65 may apply to fine, easily ignitable dust.
- Is the collector outside the building, with at least 0.1 m² of explosion vent area to the outdoors per cubic metre of enclosure volume?Yes: It meets Sentence 5.3.1.4 (1). Go to question 4.No: Go to question 3.
- Inside the building, does it have outdoor explosion venting, an automatic explosion prevention system, or a room with 1 h fire separations, outdoor venting and no other use?Yes: Sentence 5.3.1.4 (2) permits it inside. Go to question 4.No: It does not meet Article 5.3.1.4 as installed; an engineer can say which option fits.
- Is the collector’s exhaust air returned to the building?Yes: The system must keep returned air from creating an explosion hazard and shut the fan down automatically on a fire or explosion in the collector (Sentence 5.3.1.4 (3)).No: Sentence 5.3.1.4 (3) does not apply.
- Is the collector new or being modified in a factory, with a risk of ignition or explosion?Yes: An engineer’s pre-start review under Regulation 851 may also be needed before it is used, depending on the collector.No: The fire code articles above are the collector rules to check.
Article 5.3.1.4 is in Division B of O. Reg. 213/07. For the review a new or modified collector may need in a factory, see the Ontario dust collector pre-start review.
What do the woodworking and grain subsections add?
Ontario's woodworking subsection requires NFPA 664 exhaust systems, frequent shavings collection and an extinguisher or hose within 7.5 m, and its grain subsection covers silo temperatures, conveyor safety devices, separators and fog nozzles.
- 5.3.2 Woodworking. Every machine producing wood dust has a blower and exhaust system to NFPA 664, with the December 31, 2025 deeming clause for existing systems; spark-producing machines stay off those exhausts.
- 5.3.3 Grain handling and storage. Products subject to spontaneous heating are temperature-monitored; belt conveyors and bucket elevators detect misalignment or slowdown; belts are static conductive; galleries are vented to the outdoors.
Who enforces the Ontario Fire Code?
Ontario's Fire Code is enforced under the Fire Protection and Prevention Act, 1997, which makes the Fire Marshal, an assistant to the Fire Marshal or a fire chief an inspector who may enter premises and order fire safety measures.
An inspector may enter and inspect land and premises without a warrant to assess fire safety (section 19) and, after an inspection, order the owner or occupant to take any measure needed (section 21). Workplace dust rules in Regulation 851 are a separate law, enforced by the Ministry of Labour, Immigration, Training and Skills Development.
How does an Ontario fire code review differ from a pre-start review or a DHA?
An Ontario fire code review checks the building and equipment against Section 5.3, a pre-start review checks one new or modified collector against Regulation 851 before it runs, and a DHA evaluates every hazard scenario in the plant.
All three can be needed for the same project: the dust hazard analysis in Ontario page explains how the provincial rules fit together, and the electrical zoning of dust areas is covered under hazardous location classification in Ontario.
What does an Ontario fire code review cost, and how long does it take?
An Ontario fire code review of a single dust collector or process starts at $3,500–$7,500 before HST, with written findings generally within 2–4 weeks of the go-ahead, depending on how many collectors and processes the plant runs.
The estimator on this page is set to Ontario; the table of starting ranges covers every study.
Ontario Fire Code dust questions
Which Ontario buildings does Section 5.3 apply to?
Ontario buildings or parts of buildings where combustible dusts are produced in quantities or concentrations that create an explosion or fire hazard fall under Section 5.3. Article 5.3.1.1 of O. Reg. 213/07 sets that scope, the same test as the national code.
Is Section 5.10 of the Ontario Fire Code about dust?
Ontario’s Section 5.10 is reserved and holds no dust rules; the dust-producing process rules are in Section 5.3. One cross-reference in Article 5.14.6.8 still points to an Article 5.10.1.2, but the current e-Laws text of Section 5.10 reads only "RESERVED".
Does an older woodworking exhaust system still comply?
An older woodworking exhaust system still complies in Ontario if it met the Fire Code on December 31, 2025 and continues to meet those requirements. Sentence 5.3.2.1 (3) deems such systems to comply with the NFPA 664 requirement in Sentence 5.3.2.1 (1).
What air velocity do Ontario dust ducts need?
Ontario dust-collecting systems must be designed for an air velocity in the ducts of at least 1068 m/min. Article 5.3.1.11 sets that figure, which the National Fire Code of Canada 2020 does not contain.
How often should an Ontario fire code review be repeated?
An Ontario fire code review should be redone when a collector, duct or dust-producing process changes; the Fire Code itself sets no interval for it. A new or modified dust collector in a factory with an ignition or explosion risk also needs a pre-start review under Regulation 851.
What happens if an inspector finds a Section 5.3 problem?
An Ontario fire inspector who finds a Section 5.3 problem can order the owner or occupant to take any measure necessary for fire safety. Section 21 (1) of the Fire Protection and Prevention Act, 1997 gives that power after an inspection under section 19 or 20.
Sources
- O. Reg. 213/07: Fire Code (Division B, Section 5.3, Dust Producing Processes) (opens in a new tab), Government of Ontario, e-Laws.
- Fire Protection and Prevention Act, 1997 (sections 19 and 21) (opens in a new tab), Government of Ontario, e-Laws.
- National Fire Code of Canada 2020 (opens in a new tab), National Research Council Canada.
- R.R.O. 1990, Reg. 851: Industrial Establishments (sections 7 and 63 to 65) (opens in a new tab), Government of Ontario, e-Laws.
- Guideline for pre-start health and safety reviews, Item 5: Dust collectors (opens in a new tab), Government of Ontario.
- Ministry of Labour, Immigration, Training and Skills Development (opens in a new tab), Government of Ontario.