Skip to content
DustHazardAnalysis.ca
Menu

Dust Hazard Analysis in Alberta

How Alberta's OHS Code treats combustible dust, what a hazardous location requires, and which fire code applies.

Estimate your cost

Would you like to get pricing for the following equipment that will likely be required as a result of your study?

A dust hazard analysis in Alberta starts from the Occupational Health and Safety Code, which treats dust that can create an explosive atmosphere as a flammable substance. When the hazard assessment shows that such dust can be present, the work area becomes a hazardous location: it has to be classified by an engineer, and ignition sources, static electricity and access all have to be controlled. A DHA is the engineering review that shows where those areas are and what each one needs.

Who needs a dust hazard analysis in Alberta?

An Alberta employer whose work area could hold dust in ignitable concentrations has to deal with it in the hazard assessment, because the OHS Code makes flammable or explosive atmospheres a hazard, and a DHA is the engineering study that answers that question in detail.

The OHS Code defines combustible dust as "a dust that can create an explosive atmosphere when it is suspended in air in ignitable concentrations", and its definition of a flammable substance includes the same dust. A hazardous location, for Part 10, is a place where fire or explosion hazards may exist because of flammable gases or liquids, combustible dust or ignitable fibres, as described in the Canadian Electrical Code. Section 162 (1) bars anyone from entering or working where more than 20 percent of the lower explosive limit of a flammable or explosive substance is in the air.

In Alberta, grain elevators, feed and seed mills, feed warehouses and grain-seed cleaning plants are a separate case.

Because they are on the federal list of regulated industries and workplaces, these sites are generally governed by the Canada Labour Code, not Alberta's OHS Code, and the federal regulations' section 17.11 handles ignition sources wherever combustible dust is present. Your engineer confirms which set of rules your site follows.

Those workplaces, and other food and grain plants, are covered on the food, grain and feed page.

What does OHS Code section 165 require in a hazardous location?

In an Alberta hazardous location, the employer must use equipment that will not ignite the dust, control static electricity, mark or fence off the area, and have procedures that prevent a release or, where that is not reasonably practicable, prevent ignition.

  • Section 165 (3). Equipment used will not ignite a flammable substance, and static electricity is controlled: by bonding and grounding conductive containers while flammable or combustible liquids are transferred, and by some other effective means in other cases, which is where dust falls.
  • Section 165 (4). The boundaries of the hazardous location are clearly identified to warn workers of the hazard, or fenced off to keep workers and equipment out without authorization.
  • Section 165 (5). If reasonably practicable, procedures and precautionary measures prevent the inadvertent release of the flammable substance, or of oxygen that could contact it.
  • Section 165 (6). If release cannot reasonably be prevented, the procedures must instead prevent an explosive atmosphere from igniting.

Section 165 (1) and (2) are repealed; the rule on classifying the area moved to section 162.1.

Does Alberta's hazardous location rule apply to my work area?

Alberta's hazardous location rules apply wherever the Part 2 hazard assessment finds that combustible dust can create a fire or explosion hazard, and the five questions below follow the OHS Code from that first finding to the duties in section 165.

Does the hazardous location rule apply to you? 5 questions

  1. Can dust at the work area create an explosive atmosphere when it is suspended in air in ignitable concentrations?Yes: It is a combustible dust, and a flammable substance, under Part 1 of the OHS Code. Go to question 2.No: The Part 10 hazardous location rules do not apply to that dust.
  2. Has the hazard assessment required by Part 2 of the OHS Code looked at the dust?Yes: Go to question 3.No: It has to: section 161.1 makes flammable or explosive atmospheres a hazard for the purposes of Part 2.
  3. Did the hazard assessment find that the work area is a hazardous location?Yes: A professional engineer, or a competent person a professional engineer authorizes, classifies the area under section 18 of the Canadian Electrical Code, and a competent person keeps documentation of its boundaries and ignition controls (section 162.1 (1)).No: Flammable substances stored or used there must not be in a quantity that could produce an explosive atmosphere if released, among the other limits in section 163 (2).
  4. Has anything changed the basis of the classification?Yes: The employer reviews and updates the classification (section 162.1 (2)).No: The classification and its documentation stand; go to question 5.
  5. Are non-igniting equipment, static control, marked or fenced boundaries and release or ignition procedures in place in the classified area?Yes: Those are the duties of section 165 (3) to (6).No: Section 165 (3) to (6) requires them in every hazardous location.

The sections are in Alberta's Occupational Health and Safety Code (Alberta Regulation 191/2021). The engineer confirms the answers for your site; the classification duties that follow are on the Alberta hazardous location classification page.

Which fire code applies to combustible dust in Alberta?

As of November 2026, the fire code in Alberta is the National Fire Code – 2023 Alberta Edition, in force since May 1, 2024 and listed by Alberta Municipal Affairs as the fire code declared in force.

Safety codes officers in the fire discipline are certified through the Safety Codes Council, which delivers programs for the Government of Alberta under the Safety Codes Act. The engineer reads the Alberta Edition's own requirements for dust-producing processes against your site and its dust collectors.

Who enforces combustible dust rules in Alberta?

Combustible dust in Alberta falls under two systems: Alberta Occupational Health and Safety enforces the OHS Code at the workplace, and the fire code is applied under the Safety Codes Act, with fire safety codes officers certified by the Safety Codes Council.

The question of a DHA can come up at three points: when an OHS officer looks at the hazard assessment, when a safety codes officer inspects for the fire code, or when a property insurer sets its own conditions. Insurers write those into the policy, so ask yours what it expects.

How does a DHA differ from a hazardous location classification?

A hazardous location classification divides a work area into classes and zones under the Canadian Electrical Code so the right equipment is used there, while a DHA looks at the whole process for fire, flash fire and explosion scenarios and the safeguards each one needs.

In Alberta the classification is required by section 162.1 of the OHS Code once the hazard assessment finds a hazardous location, and it is done by or under a professional engineer; the duties are set out on the hazardous location classification in Alberta page. A DHA covers more ground, as NFPA 652 describes it: the process areas where hazards exist, the specific fire and deflagration scenarios, the safeguards already in place and the ones still needed.

What does a dust hazard analysis cost in Alberta, and how long does it take?

Alberta plants can budget from $8,000–$15,000 before HST for a dust hazard analysis of a single dust-producing process or collection system, with the final report usually ready 4–8 weeks after go-ahead and laboratory testing of the dust adding 3–6 weeks.

Its length depends on how many processes there are and whether the dust still has to go to a laboratory. The estimator on this page is set to Alberta and to a dust hazard analysis; a hazardous location classification is quoted as a separate study.

Alberta combustible dust questions

Is a dust hazard analysis required by law in Alberta?

A dust hazard analysis is not named in Part 10 of Alberta’s OHS Code, but the hazards it covers are: the hazard assessment must address flammable or explosive atmospheres. Section 161.1 makes those atmospheres a hazard for Part 2, and section 162.1 requires a professional engineer to classify any hazardous location the assessment finds.

Who can classify a hazardous location in Alberta?

A professional engineer, or a competent person a professional engineer authorizes, classifies a hazardous location in Alberta. Section 162.1 (1) of the OHS Code requires the classification to follow section 18 of the Canadian Electrical Code, with documentation kept by a competent person.

How often should an Alberta DHA be updated?

An Alberta DHA is normally reviewed at least every five years, the cycle NFPA 652 sets, and sooner when the basis of a hazardous location classification changes. Section 162.1 (2) of the OHS Code requires the classification itself to be reviewed and updated when that happens.

What happens if an Alberta employer never assesses its dust?

Without that assessment, an Alberta employer has no basis for the classification, equipment, static control and procedures the OHS Code requires in a hazardous location. Sections 162.1 and 165 (3) to (6) set those duties, and section 162 (1) bars work where more than 20 percent of the lower explosive limit of a flammable or explosive substance is present.

Do Alberta’s OHS rules cover a grain elevator?

A grain elevator in Alberta generally comes under the Canada Labour Code rather than Alberta’s OHS Code, because grain elevators are on the federal list of regulated workplaces. That Government of Canada list names grain elevators, feed and seed mills, feed warehouses and grain-seed cleaning plants, and section 17.11 of the federal regulations covers ignition sources around combustible dust there. The engineer confirms which rules apply to your plant.

Which fire code applies to dust in Alberta?

Alberta applies the National Fire Code – 2023 Alberta Edition to dust and every other fire hazard, in force since May 1, 2024. Alberta Municipal Affairs lists it as the fire code declared in force.

Sources

  1. Occupational Health and Safety Code, Part 10: Fire and Explosion Hazards (Alberta Regulation 191/2021) (opens in a new tab), Government of Alberta.
  2. Occupational Health and Safety Code, Part 1: Definitions and General Application (opens in a new tab), Government of Alberta.
  3. Occupational health and safety (OHS) (opens in a new tab), Government of Alberta.
  4. Fire codes and standards (opens in a new tab), Government of Alberta (Municipal Affairs).
  5. NFPA 652, Combustible Dust Awareness and Hazard Evaluation (online training series) (opens in a new tab), National Fire Protection Association.
  6. List of federally regulated industries and workplaces (opens in a new tab), Government of Canada.
  7. Canada Occupational Health and Safety Regulations (SOR/86-304), section 17.11 (opens in a new tab), Government of Canada, Justice Laws.