Skip to content
DustHazardAnalysis.ca
Menu

Combustion Risk Assessment in BC

Who needs one under WorkSafeBC's combustible dust rules, what it has to contain, and when to start.

Estimate your cost

Would you like to get pricing for the following equipment that will likely be required as a result of your study?

A combustion risk assessment in BC is the written review WorkSafeBC will expect from January 4, 2027 for any combustible dust at a workplace. It lists each way your dust could start a fire or deflagration, how serious each one is, and what in your work makes it worse. You prepare it with a qualified person, involve your safety committee or workers, and update it whenever buildings, equipment or processes change.

Who must do a combustion risk assessment in BC?

A combustion risk assessment in BC is required from every employer whose work process generates or handles a combustible dust, unless the dust is sealed in a commercial package or the workplace has no reasonably foreseeable risk of a dust combustion injuring a worker.

The duty comes from section 6.135, which first requires the employer to identify whether the dust is combustible. Section 6.134 sets the reach: any dust that goes into, comes out of or is left over from a work process counts.

The starting assumption is strict. Under section 6.137 the employer must treat the dust as ignitable and as deflagrable unless a written determination, made with a qualified person, shows otherwise. That determination rests on a screening test: the UN preliminary screening test for ignitability, and the go/no-go method in ASTM E1226-19 or ASTM E1515-14 for deflagrability, or a similar test, or published data from those tests. WorkSafeBC combustion risk assessment duties therefore apply to most dusty workplaces unless testing rules them out.

Not sure whether your dust counts? Start with the is my dust combustible checklist.

What does OHS Regulation 6.140 require in the assessment?

A BC combustion risk assessment must identify each combustion hazard for the dust and, for each one, set out the level of the combustion risk and any work processes or other factors that could increase it.

It must be in writing, prepared and updated in consultation with a qualified person, and based on these factors:

  1. the physical characteristics, location and amount of the dust on surfaces, including whether it could escape a conveying, vacuum cleaning or dust collection system and fuel a deflagration;
  2. the potential for dispersion and concentration of the dust in the air, including whether a deflagration could spread between interconnected machinery or equipment;
  3. the potential for confinement of the dust;
  4. the presence of competent ignition sources;
  5. the presence of oxidants;
  6. any other relevant factors.

WorkSafeBC's explanatory notes describe the list as aimed at the five elements of the dust explosion pentagon: fuel, suspension, confinement, ignition and oxygen.

Dust explosion pentagonFive elements around a pentagon: combustible dust (fuel), oxygen, an ignition source, dispersion of the dust in air, and confinement. Removing any one prevents a dust explosion; the first three alone can still give a fire.Fuel (combustible dust)OxygenDispersionConfinementIgnitionfire triangle:fuel + oxygen + ignition+ dispersion + confinement= dust explosion
A dust explosion needs all five elements of the pentagon: fuel, oxygen, ignition, dispersion and confinement. NFPA describes it as an expansion of the fire triangle; BC's combustion risk assessment factors in OHS Regulation s. 6.140 (2) (c) follow the same five elements.

How is a combustion risk assessment done, step by step?

A combustion risk assessment is done in six steps, from deciding whether each dust is combustible to keeping the record, with the joint health and safety committee or the worker representative consulted along the way.

  1. Decide whether each dust is combustible. Either assume it is, or obtain the written determination and test data described above.
  2. Set up the consultation. Bring in the joint health and safety committee or the worker representative, as section 6.136 requires.
  3. Walk the processes. The qualified person looks at every place dust is generated, moved, collected, stored or can settle.
  4. Rate each hazard. For each combustion hazard, record the level of risk and the factors that raise it.
  5. Act on what it finds. Where a combustion hazard is identified, a combustible dust management program and worker training follow (sections 6.141 and 6.143).
  6. Keep the record. Section 6.144 requires the date and the names of the qualified persons consulted, and the assessment is kept for as long as the dust is handled.

How long does a combustion risk assessment take, and when should it start?

A combustion risk assessment for one process or collection system typically takes 4–8 weeks from go-ahead to final report, about 3–6 weeks more where dust testing is needed, and one started before January 4, 2027 can be written to the new section from the start.

The number of processes and whether the dust still needs testing decide where a site falls in that range.

WorkSafeBC's Board approved the amendments in November 2025 and set the January 4, 2027 start date to give employers time to prepare. After that date, section 6.140 (3) requires an update as soon as practicable after a significant change to rooms, buildings or other structures, machinery or equipment, or work processes.

If you already hold a dust hazard analysis, the engineer checks it against the six factors and the consultation and record rules, and fills the gaps rather than starting over. The combustible dust management program that follows has its own requirements.

What does a combustion risk assessment cost?

A combustion risk assessment typically starts at $8,000–$15,000 before HST for one process or dust collection system, and a plant with several dust collection systems or a metal dust takes longer to assess.

Combustion risk assessment, one process or dust collection system$8,000–$15,000Starting range, before HST. The estimator on this page gives a range for your own facility.

How does a combustion risk assessment differ from a DHA and a management program?

A combustion risk assessment rates each combustion hazard of a dust, a dust hazard analysis is the NFPA 652 study that covers similar ground, and the combustible dust management program is the plan of controls that follows when a hazard is found.

The amended regulation does not mention NFPA or a DHA, so an existing DHA is checked against section 6.140 and completed where it falls short. The program has its own requirements in section 6.141, and a fire code review is separate again, as the BC Fire Code dust-producing processes page explains.

Combustion risk assessment questions

Who counts as a qualified person for the assessment?

A qualified person for the assessment is someone who meets the existing definition of "qualified" in Part 1 of the OHS Regulation. WorkSafeBC's explanatory notes for the amendments say that definition applies, and that the role may be filled by different people for different requirements.

Does a combustion risk assessment need dust testing?

A combustion risk assessment does not always need dust testing, because the employer may assume the dust is ignitable and deflagrable and go straight to the assessment. Section 6.137 allows that assumption. Testing, such as the UN preliminary screening test for ignitability or the go/no-go method in ASTM E1226 for deflagrability, is needed to show that a dust is not combustible.

Who has to be consulted on the assessment?

The joint health and safety committee has to be consulted on the assessment, or the worker health and safety representative where there is no committee. Section 6.136 requires that consultation and, where there is neither, consultation with a representative sample of the employer's workers at the workplace.

How long does the assessment have to be kept?

The assessment has to be kept for as long as the employer generates or handles the dust. Section 6.144 makes it a dust record and requires it to show the date it was prepared or updated and the names of the qualified persons consulted.

Can an existing DHA serve as the combustion risk assessment?

An existing DHA can serve as the starting point for a combustion risk assessment, which is then completed wherever the report falls short. The amended regulation does not mention NFPA or a DHA, so an existing report is checked against the six factors in section 6.140 (2) (c) and the consultation and record rules.

How often does a combustion risk assessment have to be updated?

BC employers must update a combustion risk assessment as soon as practicable after a significant change. Section 6.140 (3) of the OHS Regulation lists changes to rooms, buildings or other structures, machinery or equipment, and work processes.

What happens if there is no combustion risk assessment?

Without a combustion risk assessment, a BC employer handling combustible dust does not meet the amended regulation from January 4, 2027. Section 6.135 requires one for every combustible dust, and the management program and training in sections 6.141 and 6.143 are based on its findings.

Sources

  1. Approved amendments for Part 6, Combustible Dusts, in the Occupational Health and Safety Regulation and the Prevention Manual (opens in a new tab), WorkSafeBC.
  2. Board of Directors decision: Combustible dusts (2025/11/14-07) (opens in a new tab), WorkSafeBC.
  3. Backgrounder: Combustible dusts regulatory changes (opens in a new tab), WorkSafeBC.
  4. Upcoming amendments to requirements for combustible dusts (opens in a new tab), WorkSafeBC.
  5. NFPA 652, Combustible Dust Awareness and Hazard Evaluation (online training series) (opens in a new tab), National Fire Protection Association.