Skip to content
DustHazardAnalysis.ca
Menu

Combustible Dust Regulations in Canada

Workplace safety rules, fire codes and regulators for combustible dust, province by province, as written in the primary sources.

Estimate your cost

Would you like to get pricing for the following equipment that will likely be required as a result of your study?

Combustible dust regulations in Canada are provincial. Each province covered here handles dust through two sets of rules: its workplace safety law, enforced at the workplace, and its fire code, applied to buildings and processes. Some provinces have rules written for dust and dust collectors; others cover dust through general rules for flammable substances and explosive atmospheres. This page sets the provinces side by side as their own legal texts state them, with the numbers that set a duty in each.

What are the combustible dust regulations in Canada, province by province?

Canada's combustible dust rules differ by province: British Columbia, Ontario and New Brunswick have sections written for dust or dust collectors, while Alberta, Saskatchewan and Manitoba cover dust as a flammable substance, and each of these provinces also applies a fire code.

Combustible dust rules by province, as confirmed in the primary sources
ProvinceWorkplace safety ruleFire codeRegulatorNotes
British ColumbiaOHS Regulation Part 6, sections 6.133 to 6.159, from January 4, 2027: dust determination, combustion risk assessment, management programBC Fire Code 2024, adopting the National Fire Code of Canada 2020 with Section 5.3 unchangedWorkSafeBC; BC fire officialsCovers every combustible dust, not only wood; assessment written with a qualified person
AlbertaOHS Code Part 10: dust is a flammable substance; hazardous locations classified under section 162.1; duties in section 165 (3) to (6)National Fire Code – 2023 Alberta Edition, in force May 1, 2024Alberta Occupational Health and Safety; safety codes officers under the Safety Codes ActClassification by or under a professional engineer; entry barred above 20% of the lower explosive limit
SaskatchewanOHS Regulations, 2020, Part 25: written procedures, ignition control, hot work testsNational Fire Code of Canada 2020, in effect January 1, 2024, under The Fire Safety ActOccupational Health and Safety, Ministry of Labour Relations and Workplace SafetyExplosive dust counted as a flammable substance; entry barred above 20% of the lower explosive limit
ManitobaWorkplace Safety and Health Regulation Part 19: safe work procedures for fire and explosive hazardsManitoba Fire Code, adopting the National Fire Code of Canada 2020 from January 1, 2024Workplace Safety and Health; Office of the Fire CommissionerEntry barred above 10% of the lower explosive limit; hot work to the Manitoba Fire Code
OntarioRegulation 851 sections 63 to 65; engineer’s pre-start review for dust collectors (section 7, Table item 5)Ontario Fire Code (O. Reg. 213/07), Division B, Section 5.3, Dust Producing ProcessesMinistry of Labour, Immigration, Training and Skills Development; fire code made under the Fire Protection and Prevention Act, 1997Collectors for easily ignitable fine dust outdoors or in a vented, fire-separated room
New BrunswickGeneral Regulation 91-191: dust collector rule (section 24 (2.71)), dust control (25.2), hot work (275)National Fire Code of Canada 2020, from May 1, 2025Occupational health and safety officers of the Workplace Health, Safety and Compensation Commission; Office of the Fire MarshalCollectors over 0.6 m³ for combustible dust since April 1, 2024; Fire Marshal technical note 2019-01
Federal (federally regulated workplaces)Canada Occupational Health and Safety Regulations s. 17.11: ignition sources and hot work around combustible dust–Canada Labour Code, Part IIGenerally the grain, feed and seed workplaces on the federal list; the engineer confirms which rules apply. WHMIS: Combustible Dusts, Category 1
Other provinces and territoriesProvincial fire codes and workplace safety law apply; the engineer confirms which provisions cover your site.

Each province name links to the page for that province. The detailed rule pages are the combustible dust fire code overview, the BC Fire Code and Ontario Fire Code dust-producing process pages, the Ontario dust collector pre-start review, and hazardous location classification in general, in Ontario and in Alberta. The same rules, sorted by industry, are on the combustible dust industries page. The estimator on this page covers Ontario, Alberta, British Columbia, Manitoba, Saskatchewan and Nova Scotia, and sites across more than one province.

What federal rules apply to combustible dust in Canada?

Two federal regimes touch combustible dust: WHMIS, through the Hazardous Products Regulations, gives it a hazard class of its own, and the Canada Labour Code generally covers grain, feed and seed workplaces because they are on the federal list of regulated industries and workplaces.

The WHMIS criteria are used step by step in the is my dust combustible guide.

  • WHMIS hazard class. The Hazardous Products Regulations define combustible dust as "a mixture or substance that is in the form of finely divided solid particles that, upon ignition, is liable to catch fire or explode when dispersed in air" (section 7.17). Category 1 (section 7.17.1) covers a substance shown to catch fire or explode when dispersed in air, or one classed as a flammable solid with 5.0% or more flammable solid by weight and particles of 500 µm or less. Schedule 5 assigns no symbol, the signal word "Warning" and the hazard statement "May form combustible dust concentrations in air" or "May form explosible dust-air mixture".
  • Federally regulated workplaces. Grain elevators, feed and seed mills, feed warehouses and grain-seed cleaning plants generally come under Part II of the Canada Labour Code and the Canada Occupational Health and Safety Regulations, because they are on the federal list of regulated industries and workplaces. Which rules apply to a particular site is confirmed by the engineer.
  • Section 17.11 of those regulations. No ignition source may be used in a fire hazard area. Where work with a possible ignition source cannot be avoided near explosive concentrations or accumulations of combustible dust, the area must be substantially free of dust, dust-producing equipment stopped, openings sealed and combustibles removed or covered, with a qualified person supervising and staying 30 minutes afterward, and an extinguisher with a hose or 200 L of water at hand.

What numbers do combustible dust regulations by province set?

The combustible dust regulations by province turn on a few numbers: entry limits of 10% or 20% of the lower explosive limit, a 0.6 m³ collector volume in New Brunswick, and the 2.36 m³/s collector capacity in the fire codes.

The numbers that set a duty in each province's rules
WhereWhat the number doesRule
AlbertaWork barred above 20% of the lower explosive limitOHS Code s. 162 (1)
SaskatchewanWork barred above 20% of the lower explosive limitOHS Regulations, 2020, s. 25-11 (1)
ManitobaEntry barred above 10% of the lower explosive limitWSH Regulation s. 19.8 (1)
OntarioWoodworking collectors under 0.47 m³/s (not wood flour) exempt from the collector location ruleReg. 851 s. 65 (2) (b)
New BrunswickCollectors over 0.6 m³ internal volume, for combustible dust, must not endanger employees if they explodeReg. 91-191 s. 24 (2.71)
Fire codes in BC, SK, MB, NB (NFC 2020) and OntarioCollectors over 2.36 m³/s outside, or inside only with outdoor venting, explosion prevention or a fire-separated roomArticle 5.3.1.4

Alberta's fire code, the 2023 Alberta Edition, is left out of the last row; the Alberta page names the code in force.

Where do NFPA standards fit in Canada?

Combustible dust standards from NFPA are not law on their own in Canada; they apply where a Canadian code or regulation cites them, or where a provincial guideline points reviewers to them.

  • The standard itself. NFPA 652 calls for a DHA on new and existing processes and facility compartments where combustible dust may be present, reviewed and updated at least every five years. Since 2025 it is part of NFPA 660. What the 2025 consolidation means here is in the NFPA 660 in Canada guide.
  • Workplace rules. None of the provincial workplace rules covered here names NFPA 652, 654 or 660, and British Columbia's new Part 6 sections do not mention NFPA or a DHA.
  • Fire codes. The National Fire Code of Canada 2020 points to NFPA 68 and NFPA 69 as examples of good engineering practice and requires wood dust exhaust systems to conform with NFPA 664. The Ontario Fire Code goes further and requires explosion venting and explosion prevention systems to be designed in conformance with NFPA 68 and NFPA 69.
  • Ontario's pre-start review. The ministry guideline for dust collectors lists NFPA 652, 654, 484 and 68 among the standards a reviewer should or may use.
  • New Brunswick's Fire Marshal. Technical Note 2019-01 says the National Fire Code of Canada relies on NFPA standards (68, 69, 77, 91, 654 and 664) to help engineers design dust collection.

How does a dust hazard analysis fit these rules?

A dust hazard analysis is the engineering study that checks a facility against whichever of these rules apply, because it identifies each fire, flash fire and explosion hazard and the safeguards needed, which is what the provincial rules ask employers to control.

In British Columbia the written document the law asks for is the combustion risk assessment; in Ontario a new or modified collector with an ignition or explosion risk needs an engineer's pre-start review; elsewhere the DHA supports the employer's hazard assessment and procedures. The dust hazard analysis cost page gives the starting range for each study.

How sources are chosen and named is described under editorial standards; the privacy and terms pages cover your use of the site.

Combustible dust regulation questions

Do Canadian provinces require NFPA 652?

None of the provincial workplace rules covered here names NFPA 652, NFPA 654 or NFPA 660, so those standards are not law on their own in these provinces. They matter through fire codes that cite related NFPA standards and through Ontario’s pre-start review guideline, which lists NFPA 652.

Which province has the strictest entry limit for explosive atmospheres?

Manitoba has the strictest entry limit of the provinces covered here, barring workers above 10% of the lower explosive limit. Section 19.8 (1) of its Workplace Safety and Health Regulation sets 10%, against 20% in Alberta’s OHS Code and Saskatchewan’s regulations.

Which provinces have rules written for dust collectors?

Ontario and New Brunswick both have workplace rules written for dust collectors, separate from the fire code rule for large collectors. Ontario’s Regulation 851 section 65 sets where collectors for easily ignitable fine dust go, and New Brunswick’s section 24 (2.71) covers collectors over 0.6 m³.

How does WHMIS classify combustible dust?

WHMIS classifies combustible dust as its own hazard class, Combustible Dusts, with one category, the signal word Warning and no symbol. Sections 7.17 and 7.17.1 and Schedule 5 of the Hazardous Products Regulations set the definition, the criteria and the hazard statements.

When do British Columbia’s combustible dust rules take effect?

British Columbia’s combustible dust rules take effect on January 4, 2027. Sections 6.133 to 6.159 were added to Part 6 of the OHS Regulation by a November 2025 Board decision, which chose the date to give employers preparation time.

Which fire code edition applies in each province?

Most of the provinces covered here use the National Fire Code of Canada 2020, while Alberta uses its 2023 Alberta Edition and Ontario its own Fire Code. British Columbia adopted NFC 2020 as the BC Fire Code 2024, Saskatchewan and Manitoba from January 1, 2024, and New Brunswick from May 1, 2025.

Sources

  1. Approved amendments for Part 6, Combustible Dusts, in the Occupational Health and Safety Regulation and the Prevention Manual (opens in a new tab), WorkSafeBC.
  2. Board of Directors decision: Combustible dusts (2025/11/14-07) (opens in a new tab), WorkSafeBC.
  3. British Columbia Fire Code Order (2024) (opens in a new tab), Government of British Columbia.
  4. Occupational Health and Safety Code, Part 10: Fire and Explosion Hazards (Alberta Regulation 191/2021) (opens in a new tab), Government of Alberta.
  5. Occupational Health and Safety Code, Part 1: Definitions and General Application (opens in a new tab), Government of Alberta.
  6. Fire codes and standards (opens in a new tab), Government of Alberta (Municipal Affairs).
  7. The Occupational Health and Safety Regulations, 2020 (RRS c S-15.1 Reg 10), Part 25: Fire and Explosion Hazards (opens in a new tab), Government of Saskatchewan, Publications Centre.
  8. National Building Code, National Fire Code, National Plumbing Code and National Energy Code for Buildings (opens in a new tab), Government of Saskatchewan.
  9. Workplace Safety and Health Regulation, M.R. 217/2006, Part 19: Fire and Explosive Hazards (opens in a new tab), Government of Manitoba, Manitoba Laws.
  10. Workplace Safety and Health (opens in a new tab), Government of Manitoba.
  11. Summary of major changes 2010-2020: National Fire Code of Canada adoption (OFC 23-004) (opens in a new tab), Office of the Fire Commissioner, Manitoba.
  12. R.R.O. 1990, Reg. 851: Industrial Establishments (sections 7 and 63 to 65) (opens in a new tab), Government of Ontario, e-Laws.
  13. Guideline for pre-start health and safety reviews, Item 5: Dust collectors (opens in a new tab), Government of Ontario.
  14. O. Reg. 213/07: Fire Code (Division B, Section 5.3, Dust Producing Processes) (opens in a new tab), Government of Ontario, e-Laws.
  15. Ministry of Labour, Immigration, Training and Skills Development (opens in a new tab), Government of Ontario.
  16. General Regulation 91-191 under the Occupational Health and Safety Act (opens in a new tab), Government of New Brunswick.
  17. Safety Talk: Combustible Dust (opens in a new tab), WorkSafeNB.
  18. Bulletin 2025-01: 2020 National Model Code adoption and regulatory updates (opens in a new tab), Office of the Fire Marshal, New Brunswick.
  19. Fire inspections, plans and standards (opens in a new tab), Government of New Brunswick.
  20. Technical Note 2019-01: Dust-Producing Processes (opens in a new tab), Office of the Fire Marshal, New Brunswick.
  21. National Fire Code of Canada 2020 (opens in a new tab), National Research Council Canada.
  22. NFPA 652, Combustible Dust Awareness and Hazard Evaluation (online training series) (opens in a new tab), National Fire Protection Association.
  23. NFPA 660, Standard for Combustible Dusts and Particulate Solids (opens in a new tab), National Fire Protection Association.
  24. List of federally regulated industries and workplaces (opens in a new tab), Government of Canada.
  25. Canada Occupational Health and Safety Regulations (SOR/86-304), section 17.11 (opens in a new tab), Government of Canada, Justice Laws.
  26. Hazardous Products Regulations (SOR/2015-17), Subpart 17 Combustible Dusts and Schedule 5 (opens in a new tab), Government of Canada, Justice Laws.
  27. Workplace Hazardous Materials Information System (WHMIS) (opens in a new tab), Health Canada.
  28. Occupational Health and Safety Act (O-0.2), sections 5 and 31 (opens in a new tab), Government of New Brunswick.